Microphone Input Modules

Microphone Input Modules

Switchable Mic/Line Input with Mute-Send/Receive

Switchable Mic/Line Input with Mute-Send/Receive

ML-11T

The ML-11T is a microphone/line input module to be used in conjunction with the 900 series components and other TOA's equipment. It has a balanced microphone/line input with removable terminal block connector, phantom power supply function, and gain and tone controls.

Microphone Input

Microphone Input

M-01F

The M-01F is a microphone input module to be used in conjunction with the 900 series components and other TOA's equipment. It has a transformer balanced microphone input with female XLR type connector, phantom power supply function, and gain and tone controls.

Microphone Input

Microphone Input

M-01M

The M-01M is a microphone input module to be used in conjunction with the 900 series components and other TOA's equipment. It has a transformer balanced microphone input with male XLR type connector, phantom power supply function, and gain and tone controls.

Microphone Input

Microphone Input

M-01P

The M-01P is a microphone input module to be used in conjunction with the 900 series components and other TOA's equipment. It has a transformer balanced microphone input with φ6.3 (1/4") phone jack connector, phantom power supply function, and gain and tone controls.

Microphone Input

Microphone Input

M-01S

- For Balanced, Low Impedance Microphones. - High and Low Cut Fileters for tone control, 4.2k Hz and 330 Hz, 6 dB/octave. - Phantom Power, +22V DC for condenser-type microphones. Avtive by default, cut Jumper J1 to disable. - Connector: removable terminal block

Microphone Input with Mute-Receive

Microphone Input with Mute-Receive

M-11S

For Balanced, Low Impedance Microphones. - High and Low Cut Fileters for tone control, 4.2k Hz and 330 Hz, 6 dB/octave. - Phantom Power, +22V DC for condenser-type microphones. Activate by default, cut Jumper J1 to disable. - Responds To Mute Bus Activation, via Mute SEND module or switch-closure. - Responds To Both Mute Bus #1 And Mute Bus #2 By Default (cut jumper(s) to disconnect individual mute bus). - Two Mute Response Modes (cut jumpers to configure): 1. Normally-ON - turns OFF during mute activation (most common) 2. Normally-OFF - turns ON during mute activation (functions as an ON/OFF switch, useful for zone-paging microphones in multi-amplifier systems) - Connector: removable terminal block

Microphone Input with Remote Volume Control

Microphone Input with Remote Volume Control

M-21S

The M-21S is a microphone input module to be used in conjunction with the 900 series components and other TOA's equipment. It has a transformer balanced microphone input with screw terminals, remote volume control function, phantom power supply function, and gain and tone controls.

Microphone Input with Mute-Send

Microphone Input with Mute-Send

M-41S

The M-41S is a microphone module to be used in conjunction with the 900 series or AX-1000 amplifier.The M-41S has a phantom power supply and a 600 Ω balanced input. The module also has a voice-activated muting control output.

Microphone Input with Voice Gate

Microphone Input with Voice Gate

M-51F

The M-51F is a microphone input module to be used in conjunction with the 900 series components and other TOA's equipment. It has a transformer balanced microphone input with female XLR type connector, phantom power supply function, voice-gate function, and gain and tone controls.

Microphone Input with Voice Gate

Microphone Input with Voice Gate

M-51S

- For Balanced, Low Impedance Microphones. - High Cut Fileters for tone control, 330 Hz, 6 dB/octave. - Phantom Power, +22V DC for condenser-type microphones. Activate by default, cut Jumper J1 to disable. - Voice Gate Function, module OFF until input signal exceeds threshold. - Sensitivity Control - turn clockwise to increase sensitivity (to open gate with lower input signal) and counter-clockwise to reduce sensitivity (to open gate with higher input signal) - Connector: removable terminal block

Microphone Input with Compressor

Microphone Input with Compressor

M-61F

The M-61F is a microphone input module to be used in conjunction with the 900 series components and other TOA's equipment. It has a transformer balanced microphone input with female XLR type connector, phantom power supply function, compressor function and threshold and tone controls.

Microphone Input with Compressor

Microphone Input with Compressor

M-61S

For Balanced, Low Impedance Microphones.- High and Low Cut Fileters for tone control, 4.2k Hz and 330 Hz, 6 dB/octave.

  • Phantom Power, +22V DC for condenser-type microphones. Activate by default, cut Jumper J1 to disable.

  • - Compressor Function Helps Prevent Overload And Distortion, activates when the module's input signal exceeds a preset, adjustable threshold.

  • Compression Ratio: 2:1 (fixed), reduces the module's output signal level to 1 dB for every 2 dB increase in input siganl level.

  • Threshold Control - turn CW to lower threshold (to activate compressor function with lower input signal) and CCW to increase threshold (to activate compressor function with higher input signal).

  • Connector: removable terminal block

High Impedance Microphone Input

High Impedance Microphone Input

M-03P

The M-03P is a microphone input module to be used in conjunction with the 900 series components and other TOA's equipment. It has an unbalanced microphone input with φ6.3 (1/4") phone jack connector, and gain and high and low cut filter tone controls.

Scroll to top